Stay in Touch
Oops! Something went wrong while submitting the form
Planning a flip or a rental turn? Use this free paint calculator to see how much paint you need, room by room.
Enter each room's size, doors, windows and coats. You'll get the paintable square footage, the gallons you need (as 1-gallon and 5-gallon cans), primer, and an estimated cost. Your contractor bids and your material budget will start from the same numbers.
Wall area = 2 × (length + width) × wall height. The calculator subtracts 21 sq ft for each door and 15 sq ft for each window, and adds length × width if you include the ceiling. Gallons = paintable area × coats ÷ coverage. Coverage defaults to 350 sq ft per gallon, the typical figure on a can of interior latex. The total is rounded up to whole gallons and split into 5-gallon buckets plus 1-gallon cans. Primer is estimated as one coat over the same area.
If you're asking "how much paint do I need?", most of the answer comes down to a handful of numbers. These are the well-known ones used across the paint industry. Always check the label on your specific can, because coverage varies by product.
| Surface or product | Typical coverage (about) |
|---|---|
| Smooth, previously painted wall | 350 to 400 sq ft per gallon |
| Primer on new drywall or patches | 250 to 300 sq ft per gallon |
| Textured or rough wall | 250 sq ft per gallon or less |
| Ceiling (flat ceiling paint) | 350 to 400 sq ft per gallon |
| Standard door opening deduction | about 20 sq ft each |
| Typical window deduction | about 15 sq ft each |
A 12×12 room with 8-ft walls, one door and two windows has about 333 sq ft of wall. Two coats at 350 sq ft per gallon come to about 1.9 gallons, so buy 2 gallons of paint and 1 gallon of primer. Add about 1 more gallon if you're painting the ceiling.
If a whole-house repaint needs 4 gallons or more of one color, a 5-gallon bucket is usually cheaper per gallon and keeps the color consistent from room to room. The calculator switches to 5-gallon buckets automatically once you reach 4 gallons.
Not always. Primer matters for new drywall, patched areas, stains, and big color changes. Over clean walls in a similar color, a paint-and-primer product is often enough. Uncheck the primer box if you won't be priming.
Textured walls, bare drywall, dark colors and rolling technique can all reduce real-world coverage to 250–300 sq ft per gallon. Lower the coverage figure for rough surfaces to build in a buffer.
It depends on the room's size, but here are two examples at 350 sq ft per gallon and two coats. A 10×10 room with 8-ft walls, one door and one window has about 284 sq ft of wall and needs about 1.6 gallons, so buy 2. A 12×14 bedroom with one door and two windows has about 365 sq ft of wall and needs about 2.1 gallons, so plan on 3. Use the calculator for your own room sizes.
Multiply the room's perimeter by the wall height, subtract the doors and windows, multiply by the number of coats, and divide by the coverage per gallon. Then round up. The paint calculator above does all of this for each room and adds up the total.
A ceiling is the room's length × width. A 12×12 ceiling is 144 sq ft, so two coats take a little under one gallon at 350 sq ft per gallon. Tick "Ceiling" on the room and the calculator adds it for you.
Two coats is the usual standard. You may need an extra coat when covering a dark color with a light one, or when painting over bare or patched drywall without primer. A single coat is only enough for a quick refresh when the old and new colors are close.
Yes, a small buffer is smart. Many painters add about 10 percent for cutting in, spills and touch-ups. The calculator already rounds up to whole gallons, which often covers it. For rough walls, lower the coverage figure instead.
Yes. Switch the toggle to Meters and enter your room sizes in meters. The calculator converts to square feet behind the scenes and shows your area in square meters. Paint is still counted in gallons.
Paint is one line in a bigger scope. These ScopeFirst guides help you plan the rest of the job:
Keep paint, materials and scope for every property in one place, and send the same list to every contractor.
Start free in ScopeFirstOops! Something went wrong while submitting the form